Lectrosonics WM Digital Hybrid Wireless Beltpack Transmitter, 19 486.400 - 511.975 MHz
  • Lectrosonics Digital Hybrid Wireless Beltpack Transmitter WM for 19 Frequency Range of 486.400 - 511.975 MHz

Lectrosonics WM Digital Hybrid Wireless Beltpack Transmitter, 19 486.400 - 511.975 MHz

$2,100.00  $50.00
Save: 98% off

In Stock

Breathe easy. Free shipping and returns.
People want this. 14 people are watching this.

Condition: New

Shipping: Free Standard Shipping

Delivery: Cheap and fast delivery

Returns: 90 Days Easy Returns View More Return Policy

Payments:

Product Detail

The Lectrosonics WM Digital Hybrid Wireless Beltpack Transmitter is a top - notch device designed for wet or dusty environments. It features O - ring sealed battery compartments and input jack, a compression sealed antenna port, and a gasket sealed control panel and back cover. Using dual AA batteries, it offers twice the operating time compared to earlier watertight transmitter designs. The larger membrane switches, control panel, and a highly visible, backlit LCD greatly enhance the user experience. **Key Features** - You can select the output power (50, 100, or 250 mW) to either maximize battery life or achieve an excellent operating range. - It has a machined aluminum, corrosion - resistant housing. - Water - resistant seals make it perfect for use in wet conditions. - The LCD interface comes with a lockout option. - Programmable compatibility modes allow it to work with a wide variety of receivers. - The servo bias input circuitry has selectable voltage. **Technical Specifications** **Operating frequencies**: WM has multiple blocks including Block 470 (470.100 - 495.600), Block 19 (486.400 - 511.900), etc. **Channel Spacing**: 25 kHz or 100 kHz **Frequency selection**: Via control panel mounted membrane switches **RF Power output**: 50, 100, or 250 mW **Compatibility Modes WM**: Nu Hybrid, IFB, Mode 3 **Pilot tone**: Different deviations for Nu Hybrid and Digital Hybrid Mode **Frequency stability**: ± 0.002% **Spurious radiation**: Compliant with ETSI EN 300 422 - 1 v1.4.2 **Equivalent input noise**: - 125 dBV, A - weighted **Input level**: Varies for dynamic mic, electret lavaliere mic, and line level input **Input impedance**: Different values for different types of input **Input limiter**: Soft limiter with a 30 dB range **Bias voltages**: Selectable (2V, 4V, and Off) **Gain control range**: 44 dB, adjusted via panel mounted membrane switches **Modulation indicators**: Dual bicolor LEDs show modulation levels **Controls**: Control panel with LCD and four membrane switches **Low frequency roll - off**: Adjustable from 35 to 150 Hz **Audio Frequency Response**: 35 Hz to 20 kHz, +/- 1 dB **Total Harmonic Distortion**: 0.2% typical (Nu Hybrid mode) **Audio Input Jack**: 2.5 mm locking micro, threaded for stainless sleeve on WP connector **Antenna**: Flexible, unbreakable steel cable. **Batteries**: 1.5 Volt AA (lithium recommended) **Weight**: 5.33 oz. (151 grams) with lithium batteries **Housing Dimensions**: 2.98 x 2.55 x 0.77 inches (75.7 x 64.8 x 19.6 mm, including battery caps) **Emission Designator**: 110KF3E **Included Accessories**: 2 Dual Lithium AA Batteries, 1 Microphone (Part #M152/WP), 1 Belt Clip (Part #WMBCSL), 1 O - ring Kit (Part #ORINGKIT/WM), 1 Quickstart Guide

Using the Lectrosonics WM Digital Hybrid Wireless Beltpack Transmitter is quite straightforward. First, insert two 1.5 - volt AA lithium batteries into the battery compartment. Make sure the O - rings are in place to keep the compartment sealed. Then, connect your microphone or other audio source to the 2.5 mm locking micro audio input jack. Next, use the control panel with its membrane switches to set the frequency, output power, and other settings. You can choose an output power of 50, 100, or 250 mW depending on whether you want to save battery life or need a longer operating range. The LCD screen will show you all the important information about the settings. When it comes to compatibility, this transmitter has programmable modes that allow it to work with a wide variety of receivers. So, just select the appropriate mode for your receiver. **Note**: This transmitter is designed for wet or dusty environments, but it's still a good idea to avoid submerging it in water. Also, don't expose it to extreme temperatures. For maintenance, check the O - rings regularly for signs of wear and replace them if necessary. Keep the antenna clean and make sure it's not damaged. If you're not using the transmitter for a long time, remove the batteries to prevent corrosion. And that's it - enjoy using your high - quality wireless transmitter!


Copyright (C) sellitchet.com 2025 All Rights Reserved.